Address: Wollongong NSW
Gutters, Fascias & Eaves: The Detail That Finishes a Repaint
Why gutters, fascias and eaves fail first on Illawarra homes, and how Colourland Painting preps and paints them so an exterior repaint actually looks finished.
When people picture a house repaint, they picture the walls. But from our experience, the walls aren’t usually what makes a job look finished. It’s the gutters, the fascias and the eaves. Fresh walls under faded gutters and peeling eaves always look half done, and on the coast those are the parts that go first.
At Colourland Painting we’re second-generation painters with over 35 years combined experience around Wollongong and the Illawarra. Here’s how we handle the trim on an exterior repaint, and why we never leave it out.
Why the trim fails before the walls do
Gutters, fascias and eaves take more punishment than any wall. The fascia board and gutter face cop full sun all afternoon. Eaves sit in shade, so they stay damp and that’s where mould gets going. Salt air from the coast settles on all of it. And because nobody washes their gutters, the dirt and salt just sit there between repaints.
The result is the usual list we see on Illawarra homes: chalky, faded Colorbond gutters, timber fascias with paint lifting at the joints, and eave linings with black mould spots or water stains near the corners. None of that fixes itself. Once the sun has taken the coating down far enough, it’ll never go back to a hundred percent no matter how much prep you do. That’s why we’d rather catch it early.
Gutters: Colorbond and older metal
Most gutters around Wollongong are Colorbond or older galvanised steel. Colorbond doesn’t have a quality problem, but once it starts to fade that’s the time to paint it. Leave it longer and it starts to rust, and then you’re replacing gutters instead of painting them, which costs a lot more.
Our process for metal gutters:
- Wash down to get the salt, dirt and chalk off. Paint won’t hold to chalk.
- Sand back any loose or flaking paint and treat any surface rust. If there’s rust, it gets a proper rust primer first, the same approach we use on metal roofs.
- Prime bare metal, then two top coats of a quality exterior paint suited to metal.
If the gutters are rusted through or sagging, we’ll tell you straight. Paint won’t fix a gutter that needs replacing, and we’d rather you spend the money once.
Fascias: timber and metal
Timber fascias are where we find the most hidden damage. Paint cracks at the joints, water gets behind it, and the timber starts to soften. We probe any suspect spots before we quote. Soft timber gets cut out and replaced or repaired before any paint goes on, otherwise you’re painting over rot and it’ll be flaking again in a year.
Sound timber gets sanded, gaps filled and sealed, any bare timber primed, then two coats. Metal fascia covers get the same treatment as the gutters.
Eaves: the mould and the stains
Eave linings are usually fibre cement sheet, sometimes timber lining boards on older homes. Because they’re shaded and close to the coast, mould is the big one. We treat mould with a proper mould wash and let it do its job before anything else happens. Painting straight over mould just traps it, and it comes back through. We go into this more in our post on treating mould and coastal damp before painting.
Brown water stains near corners usually mean a gutter has been overflowing or a roof flashing is leaking. We’ll point it out so it gets fixed, then spot-prime the stains with a stain-blocking sealer so they don’t bleed through the new paint.
What paint we use
For exterior trim we use Dulux. From our experience with other brands we’ve seen paint chalk, flake or discolour. With Dulux we’ve done touch-ups on a house painted ten years ago and the colour still matched. On trim that cops the coastal weather, that track record matters. You can read more in why we use Dulux and our guide to the best paint for coastal salt-air homes.
Sheen is usually low sheen or semi-gloss on fascias and gutters, as it’s tougher and easier to wash, and flat or low sheen on eaves so they don’t highlight every joint in the sheeting.
Colour tips for trim
- If you’re keeping Colorbond roofing, matching gutters to the roof colour usually looks cleanest.
- Dark gutters and fascias look sharp, but they show fading sooner in full sun. Mid-tones hold up better on north and west faces.
- White or off-white eaves keep the underside bright and make the house feel lighter.
Can you do just the trim?
Yes. If your walls are still in good shape but the gutters and fascias are tired, a trim-only repaint is a good way to buy a few more years before the full exterior. It’s also a smart job before you sell. Most homes we see need the full exterior every 7 to 10 years, and keeping the trim up in between helps the whole job last. See how often you should really repaint and our spring exterior maintenance checklist.
One thing to keep in mind is access. Two-storey gutters and eaves need scaffolding or the right height access, and we always quote that properly up front so there are no surprises.
Getting it done
If your gutters, fascias or eaves are looking tired, we’ll come out, have a proper look, check for rot and rust, and give you a fixed written quote. We back our work with a 1-year workmanship warranty, plus the Dulux manufacturer’s guarantee on the paint.
Have a look at our exterior painting services and house painting in Wollongong, or get in touch for a free quote. You can call us on 0421 755 294.

